PIETTA FRONTIER, PISTOLERO, GREAT WESTERN II 2 MAGNA-TUSK GRIPS ~ 2P W. SCROLL

Description: Arizona Custom GripsPIETTA SAA* PIETTA / CIMARRON FRONTIER, PISTOLERO, EL MALO, etc.;* PIETTA / EMF GREAT WESTERN II (includes most GW II models); and * OTHER Misc. PIETTA SAA Style REVOLVERS (Davidson’s Exclusive 1873, etc.)(See below for further details)~ Exclusive ~ MAGNA-TUSK™WHITE IVORYSCROLL ENGRAVED GRIPSMilled out of a solid block of Magna-Tusk, denser and heavier than regular Ivory or Stag. See below for details.~~~~~two-PIECE (with SCREWHOLE) STYLETHIS AUCTION IS FOR OUR TWO-PIECE (SCREWHOLE) STYLE GRIPS. SEE BELOW.********ONE-PIECE VS. TWO-PIECE STYLE GRIPS:Note: Two-Piece style grips incorporate a visible screw and screwhole, allowing easy and quick removal for cleaning or maintenance of your revolver. One-Piece style grips do not use a screw but instead use an internal spacer. We sell both types. Both styles are traditional and historical designs and both were originally used on early Colts, so it is a matter of personal preference. Both styles of our grips will interchange and work on either style of grip frame, no matter how your revolver is currently set up. See below.One-Piece style grips (i.e., grips which do not have a visible screwhole in the grips) incorporate a user installed spacer (included with the grips) between the grip panels, as seen on many of the early Colts. The spacer supplied with your grips is sent unmounted to ensure optimum fit with your revolver, with simple, quick installation which takes about one minute or so per panel. Fully illustrated instructions are included. This results in a rock-tight fit, without the need of a screw. Preferred by many collectors for their clean lines and traditional look. One-Piece style grips are removed by removing the three backstrap screws, and pulling the grip and backstrap backwards. Reinstallation is in reverse order. Alternatively, our Two-Piece style grips (i.e., grips with a visible screw and screwhole) offer the superior convenience of quick grip removal. Our grips include a free Conversion Kit, allowing their use on revolvers that are currently set up for One-Piece style grips that do not have a grip pin. The Conversion Kit replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight on the frame, allowing no movement. This requires no modification to your revolver and gives you the advantage of the ease of maintenance of Two-Piece grips, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many collectors.Fully illustrated, detailed instructions are included with each set of grips. 06302300~~~~~WHAT THESE WILL FIT(Please read this entire section carefully): These WILL FIT any of the PIETTA Single Action Army style revolvers, with the standard sized SAA “plowhandle” grip frame, which measures around 3-1/8” tall. [Please see the notes below regarding brass gripframes if that is what you have, and also the non-standard, taller sized 1860 Army sized gripframes].This includes any of the following (all of which are made by Pietta and imported by Cimarron, E.M.F., Taylor’s & Co., etc.):• Cimarron Frontier or Stainless Frontier, Pistolero, or El Malo (NOT the El Malo 2);• Davidson’s Exclusive 1873s (sometimes also marked “Pietta 1873 Gunfighter”, “Pietta 1873 Rio” or “Del Rio Deluxe”, “Pietta 1873 Centennial”, “Pietta El Diablo”, etc.);• E.M.F. Great Western II (available in numerous variations including the Blank Firing, Buntline, Californian, Dlx Californian, Dlx Grande Californian, Cattlebrand, Dlx Stainless Steel, Express Agent (“Standard” gripframe ONLY), Frontier, Gambler’s Royale, General Patton, Gunfighter, Liberty, Midnight Special, Paladin, Pony Express (“Standard” gripframe ONLY), Posse, “R” Model, Sheriff, The Last Stand, The Shootist, U.S. Marshal, and U.S. Grant). -- Please note that these will NOT fit the “Alchimista” models – see below.• E.M.F. Hartford, Dakota II, or Dakota III;• Taylor’s & Co. TC9 revolvers with the Checkered Black Plastic grips. This revolver uses the standard (Navy sized) gripframe, measuring around 3-1/8” tall or a little under. >> Please note that these grips WILL NOT FIT the TC9 with the Checkered Walnut grips, which is a taller (1860 Army sized) gripframe, measuring around 3-1/2” tall. Please see our store and look for our Pietta 1860 grips if you have one of these.• Taylor’s & Co. Outlaw Legacy (NOT the Remington Outlaw), Single Action Stag, Cattle Brand Engraved, or other Engraved Pietta Revolvers such as Teddy Roosevelt, Patton, Cattlebrand, etc.; • Any of Pietta’s engraved SAA style revolvers being sold under various names not mentioned above, such as the Teddy Roosevelt Frontier, George S. Patton Frontier, Cimarron Buffalo Bill Cody, Cody Wild West Frontier, Bat Masterson Frontier, Outlaw Legacy, Bill Tilghman Cattleman, Cimarron Texas Ranger, etc. • Traditions Single Action Frontier or Rawhide revolvers. (Note: if your Rawhide revolver is the .22 cal. Rawhide Ranchhand, please send us an immediate followup email after your order and let us know. These require extra milling cutouts to mount properly to your frame.)• Century Arms 1873 MilleniumNote: If you do not see your pistol listed, please drop us an email with your model name and we will verify your revolver. IMPORTANT!! (Please read the following in its entirety to ensure that you get the correct grips):1) Please note that Pietta has used several different grip frame variations over the years. To ensure that we send the correct grips, when ordering please attach a message to your order stating the two-digit code found in the small rectangular box on your revolver (as shown in the 2nd picture in the listing). If you have a newer revolver and cannot find the code, please send the first three digits of your serial number so we can identify your particular revolver. If we do not hear back from you, we will send the most common version of grips to ensure we get these out on time.2) Also, if you have a BRASS gripframe (such as is sometimes found on the Cimarron “Pistolero”, Davidson’s Exclusive 1873s, EMF’s GWII “Gunfighter”, or Taylor’s “1873 Single Action Stag” revolvers, for example), please attach a note to your order informing us. 3) Finally, please note that these WILL NOT fit Pietta gripframes that are around 3-1/2” tall (such as EMF’s Alchimista, or Cimarron’s Bad Boy or El Malo 2). Your grips should measure around 3-1/16” to 3-1/8” tall, depending on how you hold your ruler or caliper. Please check this carefully before ordering. If your grips measure 3-1/2”, our Pietta 1860 Army grips are milled to fit these, which you can find in our store. Please feel free to contact us if you cannot locate what you need. What these WILL NOT FIT: These WILL NOT FIT any revolvers from other makers (such as Uberti, Armi San Marco, Colt, Ruger, etc.). Also, these will NOT fit revolvers using a gripframe that is not the standard “plowhandle” shape, such as the Bisley, the Birdshead, the Thunderer, Thunderball, or the Lightning style gripframes, nor any of the Remington style revolvers such as the 1858, 1875, or 1890. Please take a careful look at the shape of your gripframe. These are for the “plowhandle” style revolvers only.08152300A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. 23071945 Arizona Custom Grips About our exclusive Magna-Tusk™ “Hi-Grade” Ivory Grips: Our Ivory grips, an exclusive of Arizona Custom Grips, are made out of a premium high-grade, ultra-high density ivory material (Magna-Tusk™), designed from the ground up as a premium grip material to greatly improve on the inherent fragility and weakness of the cheaper Bonded Ivory used on just about all factory and regular aftermarket ivory grips today. Standard Bonded Ivory is brittle, and tends to weaken and develop stress fractures over time with repeated use, firing, and handling. Magna-Tusk™ is capable of withstanding the heaviest recoil and impact, and is the toughest alternative Ivory grip material available today, while still retaining the pristine look of real ivory. These grips are not cast or made out of an inferior, lightweight material, but are heavy and dense, carefully milled out of a solid block, one at a time. Magna-Tusk is completely rock-solid, stable, and water, chemical, and oil resistant. It is flame and heat resistant, will not melt like Urethane or plastic, and is entirely void-free, with over 10x the strength, durability, and impact resistance of alternative materials. Unlike with real ivory, there is no routine care and maintenance involved, with no danger of it drying out and cracking if not maintained properly or if left in the heat. It is produced with outstanding aesthetic properties and mechanical performance. When aged with our exclusive aging process, it takes on the equivalent of a 100-year-old patina, with subtle grain details which most experts cannot tell apart from the real thing. In addition, the material has a fine grain structure, which holds intricate detail for carvings, artistic relief work, etc., found on many historic grips. Please note that the photo used is a stock photo (a sample pair). Yours will appear similar to these. Customer satisfaction is important to us. Full money back, less shipping, if not fully satisfied.

Price: 89.95 USD

Location: Mesa, Arizona

End Time: 2024-02-16T02:49:55.000Z

Shipping Cost: 5.99 USD